Showing posts with label kitchen remodel. Show all posts
Showing posts with label kitchen remodel. Show all posts

Tuesday, December 7, 2010

Kitchen Remodel: Ikea Love

Last week when I shared some photos of our kitchen after our diy tile backsplash, I also gave you a sneak peak of something else we'd done in the kitchen but I hadn't spilled the beans about on this here ole' blog yet.

Can you spot it?


We added an organizational rail system from Ikea to the empty area on the wall to the left.


See, back before this blog even existed and we were installing our new laminate flooring, we realized that any kitchen layout changes needed to be made right-then-and-there. So, we decided to add a new bottom cabinet - because funnily enough, the existing layout didn't have a bottom cabinet for storage pots and pans and such - nope, there were just drawers, a lazy susan, the cabinet under the sink, and several very thin cabinets for storing cutting boards, which left us high and dry for anywhere at all to store our stockpots and other large cooking items (and Barley's food!).

So we bought a new unfinished cabinet from Lowe's, and removed the door from an upper cabinet to replace the shaker-style door the new cabinet came with. Thank goodness that open cabinets are in - because we looked and looked and they don't make this style of cabinet doors anymore!

Old photo showing the new
cabinet addition with paint and door.

Anyways, the new cabinet has been amazing and gives us tons of much-needed storage, and not to mention even more much-needed countertop space! But the new addition left us with an awkward situation:


Yup, a blank section of the wall.

We considered numerous options:

1) An additional upper cabinet - which we shot down because we didn't think we would find one to match our cabinets from 1968, and it would make the dining area feel more closed-in.

2) Floating shelves like the ones in our dining area  - which we also shot down because we thought they would look odd next to the open cabinet, not to mention that we already had some in our dining area.

3) Or some sort of artwork - which we shot down because we wanted something that contributed to the function of our kitchen, and something that made the new cabinet addition seem like an intended part of the kitchen.

So for a year now we've been stumped.

That is, until my parents kindly offered to bring us some Ikea loot when they drive up to Nebraska from their home in Florida (it's no fun being 1300 miles from the nearest Ikea!). After spending hours scouring the Ikea website and trying to figure out what-the-heck-that-odd-looking-thing-is-for-and-which-organization-system-it-goes-with (seriously, those small kitchen organization parts are so confusing online!),we found the perfect solution: a rail system.

To install it, Tom made the appropriate measurements:



Inserted a couple of drywall anchors:



And simply drilled in some screws.


Total awesomeness.

It instantly added an industrial kitchen-type feel to the area, and truly made that blank wall part of the kitchen. If you didn't know better, it looks like we just planned it that way intentionally!


Not knowing beforehand how many organizational canisters we'd need (or even how many rails we'd end up using), we chose 3 white canisters and 3 stainless steel ones, which we ended up mixing and matching on the top 2 rails.


In these we stored some random kitchen utensils, and other random things (like a cheese grater and ice cream scoop) for easy access. Putting our much-used kitchen supplies on the wall really freed up alot of drawer space for other things! (like towels and linens and ziploc bags). Not to mention that we were able to free up counter space by eliminating the need for our utensil holder that we used to have sitting out.


For the middle rail, we stashed important items like measuring spoons and cups, as well as our slew of spatulas.


For the bottom rail (which conveniently overlaps the backsplash), we hung up some of the prettier much-used utensils and even some fancy Williams-Sonoma oven mitts for easy access (and yes, some eye candy, too!).


So that's how we solved our awkward-empty-kitchen-wall-space dilemma without sacrificing price or style, and gained some much-needed storage. We also love how it gives off that "kitchen" vibe, without being too kitschy, and blends in and matches the rest of our kitchen. And of course, adding storage while lightening the load on our drawers and countertops is always a plus, too!



What do you think? Do you have an Ikea near you? Do you love their rail systems? If you have one, what do you use it for? (we've seen them used anywhere from bathrooms to kitchens to office areas!). Let's talk about awesome Ikea storage solutions!

Did you enjoy this post? Please subscribe for free updates in the future and to see what we're up to next!

Tuesday, November 30, 2010

Kitchen Remodel: DIY Tile Backsplash Reveal

Oh, how I love reveals. And before & afters. Aren't they just the best? Honestly, they gave me hope and inspiration when we first laid our mitts on the keys to our humble home, because, well, it was really very humble, if you get my drift.

So when I looked at this flower-power kitchen straight out of the 70's:



I managed to see a glimpse of a kitchen that was light and bright, airy but warm...


beautiful and sparkling...


and 100%...


us.

May I present: Our Kitchen.
Date: Current Day.





It still amazes me that we've done every. single. thing. in this kitchen remodel - by ourselves. Heck, half most of the time we have no idea what we're doing! Complete amateurs here. But with a "sure, we can do that, let me just google it real quick and we'll get started" attitude, anything can happen.

The proof is right here.

Drywalling? No problem. Installing flooring? Piece of cake. Tiling new countertops and backsplash? Easy peasy.

Well... sorta.

Either way, we love it.

Here's a night shot showing off our DIY undercabinet lighting

Was the kitchen backsplash worth it? Definitely.

It wasn't that hard, it just took alot of elbow grease. And in the end, you want to know what the total was?

$80. Eighty bucks. I'd call that a successful DIY project, wouldn't you?

We wrote a series of 3 tutorials detailing every step of the way, too:

How To DIY Kitchen Tile Backsplash:
{Phase 1} Tiling
{Phase 2} Grouting
{Phase 3} Sealing and Caulking

I can honestly say that the number of To-Do's in the kitchen remodel is slowly dwindling. Haha, yes, we're not quite done yet... so I guess you'll just have to stick around to see what else we have up our sleeves!

Did you enjoy this post? Please subscribe for free updates in the future and to see what we're up to next!

Monday, November 22, 2010

Kitchen Remodel: DIY Tile Backsplash {Part 3}

If you've been following along, then you'll know that we last left off with {Phase 1}, where we had put down the tiles with adhesive, and so now they were ready to look professional - so bring on the grout!


How To DIY a Tile Backplash: Phase 2 {Grouting}

1) Gather your supplies. To grout your tiles, you'll need:

Grout (we used white unsanded grout, which is for smaller grout lines)
Buckets filled with water
Grout Sponges (they're the big ones at the home improvement store)
Tile Float
Toothpicks

And don't forget to cover your work area with something protective. I used old towels to protect the existing countertop.

2) Mix up your grout (or grab your bucket of premixed stuff if you're lazy). I used a paint stir stick to stir mine... which I wouldn't recommend you do. I noticed while I was stirring it, that the blue ink was coming off of the stick into our pretty white grout. Ssshhhh, don't tell anyone. ;)


3) After letting the grout mixture sit for 10 minutes to "set up", grab your float and get a goop of grout and squish it into the cracks between the tile. Holding the float at about a 45 degree angle, push the grout into the cracks using the small end of the float, trying not to let any air bubbles get trapped in there.



4) Get off excess grout by using the long side of the float and going across the surface of the tiles at an angle, which should scoop up excess grout and leave the remaining grout in the cracks. This step makes the sponging-step much, MUCH easier.


5) Work in small sections. I usually did 1/3-1/2 of each wall, then it was time for the water buckets and sponges.


6) After the grout has dried for about 20-45 minutes, take a sponge and dip it in the water bucket. Wring out the excess water until the sponge is just barely damp.


7) Take the sponge and gently go across the tiles - this will take up the excess grout.


8) Rinse the sponge in the water bucket and repeat. Alot. After each pass, make sure to clean off your sponge in the water bucket - or else you'll just keep getting grout back on the tiles and make a huge mess (and headache). If your water gets really dirty, replace it with clean water.


9) Scope out the places where you want to caulk instead of grout. Usually this is anywhere 2 different planes meet (like corners), as well as the small area where the backsplash will meet the countertop. Don't get any grout in these areas - if any does get in, take a toothpick and pick it out before it dries.


10) After the grout dries (we waited 24 hours), take a clean cloth to it and gently buff out the existing grout haze left on the tiles.


11) Step back and admire your beautiful grout work!


While grouting isn't the funnest thing to do, I thought it was way easier than laying the tiles with adhesive. All-in-all it only took me about 5.5 hours to grout the whole thing by myself, and that includes the time it takes to prep the work area and mix the grout, along with various trips outside to dump out dirty water and refill the buckets. Grouting was time consuming, certainly, but it wasn't that hard.

Next up we'll seal the grout and tiles so they'll be stain and water-resistant (always a good thing in the kitchen!), and we'll also tackle the caulking (which proved trickier than we thought!), so head on over here to check out Phase 3! Then it'll be time for what you've been waiting for: the big reveal!
Did you enjoy this post? Please subscribe for free updates in the future and to see what we're up to next!

Thursday, November 18, 2010

Kitchen Remodel: Tile Backsplash {Part 2}

Yesterday I gushed all about our kitchen, and even gave you a little history lesson in the countless projects we've done in the heart of our home.

Today I will show you how we DIY tiled our own kitchen backsplash, improving the look and function of our kitchen for very little money (less than $100!). Honestly, tiling isn't difficult, it's just time-consuming, but if you're up to the challenge, read on for Phase 1 of a 3-Phase tutorial!


How To DIY a Tile Backsplash: Phase 1 {Laying the Tiles}

1) Gather your tools. For this part, you'll need:

Wet Tile Saw (or Tile Cutter)
Tile Adhesive (we used Type 1 in white, for wet-areas)
Tiles (we used white ceramic 3x6" subway tiles from Lowes, along with the matching edge tiles)
Tile spacers (we used 1/18", the same as our granite kitchen countertops)
Notched Tile Trowel (we used one with 1/4" notches)

2) Make sure the surface you're tiling is clean. In most backsplash cases (except for an area that will get directly wet repeatedly, like a shower wall), you can tile right over the existing drywall. Also in most cases, it's usually recommended that if the drywall isn't in good condition (or suffered from a previous tile backsplash), that you replace the drywall before tiling.


But honestly - we HATE drywalling. We've tiled over uneven surfaces before, and we were positive that the slightly bumpy existing drywall and old adhesive wouldn't pose a problem for us. Onto the next step!

3) Decide on a pattern. It's best to lay out your tiles somewhere before starting that way you'll know you'll like the placement before you begin - because once those babies start to dry, you won't really want to rip them out and start over again. Believe me.

For our pattern, we decided to stagger the tiles 1/4 the width of each tile (you can do all sorts of staggering on these tiles - I've seen 1/2, 1/3, and 1/4).

4) Protect any other surfaces. Tile adhesive is messy stuff - and once it dries, it's usually next to impossible to get off. So wear your paint clothes and protect stuff like countertops and outlets before beginning (we taped off the adjoining edge of the countertop with masking tape, and used towels to protect the rest of the countertops. We just put masking tape over the outlets.).


5) Start tiling! Dip the Notched Trowel into the adhesive and smear it onto the wall, and then take the notched end and drag little lines through the adhesive. It's sorta like working a zen garden.



Well, except without the soothing music and relaxation.

6) Once you've got a little area with adhesive on it, take your tile and plop it on the adhesive (you can also "butter" the back of the tiles with adhesive to get more grip, but it's not strictly necessary). Then just wriggle it around for a bit to get any air out from under the tile and to make the tile stick better.


Just think of it as squishing out the air from underneath one of those plastic suction cup things that you put on windows and stuff? After you spit on it (believe me, spit works the best), you push it up against the glass and get the extra air out, and it creates a vacuum/suction which holds the suction cup in place. Even when you try to get it OFF the window, it doesn't want to come off. Yeah, just imagine that, but with tile. And your "spit" is the tile adhesive. Got it? (By the way, this is exactly why I don't have a career in teaching. Just FYI.)

7) Put up another tile and use spacers to make sure they're an exact distance apart. Make sure no adhesive gets on the top of your tile, and that not too much gets in between them (since that's where the grout goes).


8) Okay, now repeat steps 5 and 6. And repeat. Repeat. Repeat. Repeat.... x100 (or however many tiles you're putting up). As you go along and start running out of spacers, you can take off the spacers from the ones that have started drying and re-use those.



9) When you get to corners or electrical outlets, you'll probably need to make some cuts on the wet saw. You'll probably also have to get creative when an outlet falls right in the middle of a tile. Yeah, after 5 attempts, we finally got it. And we're still thankful that the outlet plate will cover most of that one. Whew.


10) Make sure to keep a small space (about 1/4" inch or slightly smaller) between the bottom row of tiles and your kitchen countertop.



11) Make sure your tiles are level with one another. Oh, and make sure you have a furry supervisor at all times.


12) All-in-all, it's pretty easy! Right? No? Haha, either way by this step I'm sure you're already loving it. So, after waiting around 24 hours for the adhesive to dry, wipe any substances off your tiles (I had to use a scrubby sponge followed by a microfiber cloth to get off any particles), and now you're ready to grout!


Just look at that beautiful tiling job.


It sure adds alot to the kitchen, doesn't it?

Before Tiles:


After Tiles:


Just wait until you see it with grout! Grout really adds that finishing touch and makes everything look gorgeous and (dare I say it?!) professional. So, if you're ready, head on over here for Phase 2 {Grouting} of a DIY Tile Backsplash!

What about you? Anyone going to be tackling their own kitchen backsplash soon (especially if it is $100 or less)?

Did you enjoy this post? Please subscribe for free updates in the future and to see what we're up to next!
Related Posts with Thumbnails